3M™ Scotchfil™ 110 Electrical Insulating Putty (38mm x 1,5mx 3,17mm) - MobilCom.UA CABLE & Connectors fibre-optical Coaxial 50 Ohm 75 Ohm Twisted pair FTP UTP Connectors & Adapters N BNC TNC SMA SMB F UHF mini UHF MCX-MMCX FME NIPPLE 7/16 Pigtail Jumper N -N Jumper 7/16-7/16 Optical patching cord TAPE Scotch 3M Tools

3M™ Scotchfil™ 110 Electrical Insulating Putty (38mm x 1,5mx 3,17mm)
[932IZOLScochfi]

Click to enlarge <a href="https://mobilcom.ua/images/Scotch/932IZOLScochfi.gif?osCsid=375f314f3d8ed0dd64fbe9d03a789beb" target="_blank"><img src="images/Scotch/932IZOLScochfi.gif" border="0" alt="3M™ Scotchfil™ 110 Electrical Insulating Putty (38mm x 1,5mx 3,17mm)" title=" 3M™ Scotchfil™ 110 Electrical Insulating Putty (38mm x 1,5mx 3,17mm) " hspace="5" vspace="5"><br>Click to enlarge</a>

797,73ãðí

Scotchfil^™Electrical Insulation Putty

Data Sheet

1. Product Description

Scotchfil™ Electrical Insulation Putty is an electrical grade putty in a tape form. Scotchfil putty is UL Recognized as a splice insulation for electrical conductors at temperatures up to 176°F (80°C) when over-wrapped with either Scotch™ Super 33+ or Super 88 vinyl Electrical Tape.

UL “Recognized” Category OCOT2, File No. E59951

Noncorrosive, synthetic rubber

Excellent electrical properties

Excellent aging properties

Will not dry out

Applies cleanly without waste

Typical Properties

2. Applications

To insulate low voltage (600 volts and less) connections

To build up cable splices and fill out major irregularities and voids in low voltage splices (2300 volts and less) in order to obtain a uniform base for further taping

To round out high voltage connections

To smooth bus bar irregularities

To create a resin dam in resin pressure splices

To create a moisture seal at ground wire exit in high voltage splices

To moisture seal multiconductor cable connections

Physical Properties
Color	Black
Thickness ASTM D-1000	125 mils (3, 17 mm)
Elongation ASTM D-1000	1000%
Copper Corrosion	None
Electrical Properties
Dielectric Strength ASTM D-1000	575 V/mil (22,6 kV/mm)

Insulation Resistance ASTM D-1000

3. Specification

The insulating putty must be in tape form, the thickness of which must be a minimum of 100 mils (2,54 mm). The tape must be a rubber based tape capable of being formed and molded with moderate finger tension at temperatures as low as 32°F (0°C). Neither the tape nor any of its components shall cause the corrosion of copper. The tape must be compatible with most synthetic cable insulation as well as other splicing tapes.

4. Engineering/Architectural Specification

All 2300 volt or less feeder connections, taps and splices, on wires larger than 6 AWG with irregular shaped

>10⁶Megohms

connectors, shall be first built up with electrical insulating putty to eliminate both sharp corners and voids. Enough insulating putty shall be used until good overall padding is provided. Compress putty to fill all voids and generally smooth up before applying electrical splice protection.

All 600 volt or less splices and terminations on wires larger than 6 AWG with irregular shaped connectors shall be insulated with a minimum of 1/4 inch (6,3 mm) of electrical insulating putty. The entire connection must be covered with the insulating putty. The insulating putty must then be over-wrapped with a vinyl tape applied with the same tension as it has when it comes from the roll. This vinyl tape shall provide an uniform covering of at least four layers, half lapped in two directions.

5. Installation Techniques

To round out irregular connections, mold and pack Scotchfil Electrical Insulation Putty with moderate finger pressure, eliminating voids and air spaces. The layers of Scotchfil will fuse into a homogeneous mass. Over-wrap with two half lapped layers of Scotch Super 33+ or Super 88 Vinyl Electrical Tape.

To create a resin dam in resin pressure splices, wrap a layer of moderately stretched Scotchfil insulation putty around the cleaned cable jacket at a distance of 3.0 inches (7,6 cm) from the jacket cutback. Lay the ground wire along the cable jacket and through the Scotchfil putty. Wrap several layers of highly elongated Scotchfil putty around the cable and ground wire. Bind Scotchfil putty tightly with several wraps of Scotch Super 33+ or Super 88 Vinyl Electrical Tape. The putty and vinyl tape will make a seal through which resin cannot flow.

Important Notice

All statements, technical information, and recommendations related to Seller’s products are based on information believed to be reliable, but the accuracy or completeness thereof is not guaranteed. Before utilizing the product, the user should determine the suitability of the product for its intended use. The user assumes all risks and liability whatsoever in connection with such use.

Any statements or recommendations of the Seller which are not contained in the Seller’s current publications shall have no force or effect unless contained in an agreement signed by an authorized officer of Seller. The statements contained herein are made in lieu

Electrical Products Division

6801 River Place Blvd. Austin, TX 78726-9000 800/245 3573 FAX 800/245 0329

6. Shelf Life

Scotchfil Electrical Insulation Putty has a 5 year shelf-life (from date of manufacture) when stored under the following recommended storage conditions. Store behind present stock in a clean dry place at a temperature of 70.F and 40-50% relative humidity. Good stock rotation is recommended.

7. Availability

Scotchfil Electrical Insulation Putty is available in 1 1/2 in x 60 in (3,8 cm x 152,4 cm) rolls from your local 3M authorized electrical distributor.

of all warranties, expressed or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose which warranties are hereby expressly disclaimed.